HAS-Motion Software Documentation

User Tools

Site Tools

You are here: Main Page » visual3d » documentation » pipeline » event_commands » Event Global Maximum
visual3d:documentation:pipeline:event_commands:event_global_maximum

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
visual3d:documentation:pipeline:event_commands:event_global_maximum [2025/04/28 15:38] – wikisysopvisual3d:documentation:pipeline:event_commands:event_global_maximum [2025/08/21 17:49] (current) – wikisysop
Line 43: Line 43:
 |**!/FRAME_OFFSET=**               | Number of frames to shift the result event forward or backward from the identified maximum. | |**!/FRAME_OFFSET=**               | Number of frames to shift the result event forward or backward from the identified maximum. |
 |**!/TIME_OFFSET=**                | Time (in seconds) to shift the result event from the identified maximum. | |**!/TIME_OFFSET=**                | Time (in seconds) to shift the result event from the identified maximum. |
-|**!/EVENT_SEQUENCE=**             | Defines the sequence of events within which the search should occur. | +|**[[visual3d:documentation:c3d_signal_types:event_label_data_type|!/EVENT_SEQUENCE=]]**             | Defines the sequence of events within which the search should occur. | 
-|**!/EXCLUDE_EVENTS=**             | Events that will exclude a sequence if found within it. |+|**[[visual3d:documentation:c3d_signal_types:event_label_data_type|!/EXCLUDE_EVENTS=]]**             | Events that will exclude a sequence if found within it. |
 |**!/EVENT_SEQUENCE_INSTANCE=**   | Specifies which instance of the sequence to use (0 = all, 1 = first, -1 = last, etc.). | |**!/EVENT_SEQUENCE_INSTANCE=**   | Specifies which instance of the sequence to use (0 = all, 1 = first, -1 = last, etc.). |
 |**!/EVENT_SUBSEQUENCE=**          | Define a narrower range within the main event sequence to search. | |**!/EVENT_SUBSEQUENCE=**          | Define a narrower range within the main event sequence to search. |
Line 56: Line 56:
  
 {{:visual3d:documentation:pipeline:event_commands:egm_dialog.png?500|}} {{:visual3d:documentation:pipeline:event_commands:egm_dialog.png?500|}}
 +
 +  * **New Event Label Name**: Name for the event that will be created at the global maximum.
 +  * **Signal Component**: Signal direction selection (X, Y, Z).
 +  * **Frame Offset**: Number of frames to shift the created event forward or backward from the maximum point.
 +  * **Time Offset**: Shifts event by time (in seconds).
 +  * **Threshold**: Min. signal value required to accept a maximum.
 +  * **Event Sequence and Instance for range**: Search for maximum based on event ranges.
 +  * **Subsequence and Instance within the Event Sequence**: Search inside a sub-range within the event sequence.
  
  
Line 75: Line 83:
  
  
-=== Example 1: Simple Use Case ===+==== Example 1: Simple Use Case ====
 This example will be done showing both the dialog box and corresponding command text. This example will be done showing both the dialog box and corresponding command text.
  
Line 123: Line 131:
 ---- ----
  
-=== Example 2: Exclude Sequence ===+==== Example 2: Exclude Sequence ====
  
 In this example an event **BAD** was created between one sequence of **RHS + RHS**. Using the same parameters as the previous example, set the **Exclude Sequences containing events** parameter to **BAD** In this example an event **BAD** was created between one sequence of **RHS + RHS**. Using the same parameters as the previous example, set the **Exclude Sequences containing events** parameter to **BAD**
Line 152: Line 160:
 ---- ----
  
-=== Example 3: Subsequence ===+==== Example 3: Subsequence ====
  
 Subsequences can be used to create an event that occurs within a sequence within a sequence. Subsequences can be used to create an event that occurs within a sequence within a sequence.
  
-In this example **RKFlex_Max** was created as the maximum value between **LTO + LHS** when these events feel between the **RHS** events.+In this example **RKFlex_Max** was created as the maximum value between **LTO + LHS** when these events fall between the **RHS** events.
  
 Using the same parameters as the previous example, set the **Subsqeuence** parameter to **LTO + LHS** Using the same parameters as the previous example, set the **Subsqeuence** parameter to **LTO + LHS**
visual3d/documentation/pipeline/event_commands/event_global_maximum.1745854717.txt.gz · Last modified: 2025/04/28 15:38 by wikisysop