visual3d:documentation:pipeline:event_commands:event_modify
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revision | |||
| visual3d:documentation:pipeline:event_commands:event_modify [2025/04/11 16:02] – wikisysop | visual3d:documentation:pipeline:event_commands:event_modify [2025/04/28 19:06] (current) – wikisysop | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Event Modify ====== | ====== Event Modify ====== | ||
| - | ==== Overview ==== | + | ===== Overview |
| The **Event_Modify** command is used to adjust the timing of existing events by modifying their frame or time values. This command is useful for refining event placement, correcting errors, or aligning events with a new reference point. Users can modify events based on either frame numbers or time values. | The **Event_Modify** command is used to adjust the timing of existing events by modifying their frame or time values. This command is useful for refining event placement, correcting errors, or aligning events with a new reference point. Users can modify events based on either frame numbers or time values. | ||
| Line 8: | Line 8: | ||
| **Note**: All times will be rounded to nearest POINT frame. | **Note**: All times will be rounded to nearest POINT frame. | ||
| - | ==== Pipeline Command ==== | + | ===== Pipeline Command |
| The command below is as seen in the Visual3D application. | The command below is as seen in the Visual3D application. | ||
| Line 21: | Line 21: | ||
| </ | </ | ||
| - | ==== Command Parameters ==== | + | ===== Command Parameters |
| The following table shows the command parameters and descriptions: | The following table shows the command parameters and descriptions: | ||
| Line 31: | Line 31: | ||
| |**!/ | |**!/ | ||
| - | ==== Dialog ==== | + | ===== Dialog |
| Due to the simplicity of this command and the interactive selection option, this command does not display a dialog box when clicked, instead parameters can be edited within the text editor. | Due to the simplicity of this command and the interactive selection option, this command does not display a dialog box when clicked, instead parameters can be edited within the text editor. | ||
| - | ==== Examples ==== | + | ===== Examples |
| The following examples will go through the use of the **Event_Modify** command in the Visual3D application. | The following examples will go through the use of the **Event_Modify** command in the Visual3D application. | ||
| - | === Example 1: Modifying an Event by Time Value === | + | ==== Example 1: Modifying an Event by Time Value ==== |
| This example adjusts the RHS event from 1.28 seconds to 2 seconds. You can check the "Old Time" of an event by left clicking on it within the data tree. This dialog shows the time value we are changing: | This example adjusts the RHS event from 1.28 seconds to 2 seconds. You can check the "Old Time" of an event by left clicking on it within the data tree. This dialog shows the time value we are changing: | ||
| Line 56: | Line 56: | ||
| After running this pipeline, we can see from the dialog again that the time of the event now displays as 2 seconds. | After running this pipeline, we can see from the dialog again that the time of the event now displays as 2 seconds. | ||
| - | === Example 2: Combine in a workflow with Event Detection === | + | ==== Example 2: Combine in a workflow with Event Detection |
| We can find the maximum left hip angle throughout the full trial. Let's say we want any values 5 seconds following the max: | We can find the maximum left hip angle throughout the full trial. Let's say we want any values 5 seconds following the max: | ||
| Line 100: | Line 100: | ||
| ---- | ---- | ||
| - | ==== Notes ==== | + | |
visual3d/documentation/pipeline/event_commands/event_modify.txt · Last modified: 2025/04/28 19:06 by wikisysop