HAS-Motion Software Documentation

User Tools

Site Tools

You are here: Main Page » visual3d » documentation » pipeline » model_commands » Model Commands Overview
visual3d:documentation:pipeline:model_commands:model_commands_overview

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
visual3d:documentation:pipeline:model_commands:model_commands_overview [2024/11/12 13:50] – wikisysopvisual3d:documentation:pipeline:model_commands:model_commands_overview [2024/11/16 22:40] (current) – [Add_Landmark] wikisysop
Line 23: Line 23:
 <code> <code>
 ! New Workspace ! New Workspace
- 
 File_New File_New
 ; ;
  
 ! Set a path for the location of the data ! Set a path for the location of the data
- 
 Set_Pipeline_Parameter Set_Pipeline_Parameter
 /PARAMETER_NAME=FOLDER /PARAMETER_NAME=FOLDER
Line 35: Line 33:
  
 ! Set the parameter for the static file ! Set the parameter for the static file
- 
 Set_Pipeline_Parameter Set_Pipeline_Parameter
 /PARAMETER_NAME=STATIC /PARAMETER_NAME=STATIC
Line 43: Line 40:
 ! Apply the model template using the static trial.  ! Apply the model template using the static trial. 
 ! Leaving the **MODEL_TEMPLATE** parameter blank will bring up a dialog that allows the user to browse and select the model template ! Leaving the **MODEL_TEMPLATE** parameter blank will bring up a dialog that allows the user to browse and select the model template
- 
 Apply_Model_Template Apply_Model_Template
 /MODEL_TEMPLATE= /MODEL_TEMPLATE=
Line 72: Line 68:
 ; ;
 </code> </code>
-===Close_Model_File===+ 
 +====Append_Model_Template==== 
 +[[visual3d:documentation:pipeline:model_commands:Append_Model_Template]] 
 + 
 +<code> 
 +Append_Model_Template 
 +! /CALIBRATION_FILE= 
 +! /MODEL_TEMPLATE= 
 +! /VIEW_BUILDMODEL_RESULTS=2 
 +; 
 +</code> 
 + 
 +====Close_Model_File====
  
 [[visual3d:documentation:pipeline:model_commands:close_calibration_file|Close_Model_File]] [[visual3d:documentation:pipeline:model_commands:close_calibration_file|Close_Model_File]]
Line 92: Line 100:
 </code> </code>
  
-===Assign_Model_File=== +====Assign_Model_File==== 
-[[Visual3D:Documentation:Pipeline:Model_Commands:Assign_Model_File|Assign_Model_File]] - Assign a Model to a Movement File                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |+[[Visual3D:Documentation:Pipeline:Model_Commands:Assign_Model_File|Assign a Model to a Movement File]]                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      |
  
 <code> <code>
Line 138: Line 146:
 Another example can be found on [[Visual3D:Documentation:Pipeline:Model_Commands:Assign_Model_File_Example|Pipeline Example using Assign Model File]] Another example can be found on [[Visual3D:Documentation:Pipeline:Model_Commands:Assign_Model_File_Example|Pipeline Example using Assign Model File]]
  
-===Create_Hybrid_Model=== +====Create_Hybrid_Model====
-|     [[Visual3D:Documentation:Pipeline:Model_Commands:Create_Hybrid_Model|Create_Hybrid_Model]] - Create a Visual3D Hybrid Model                                                                                                                                                                                                                                                                                                                                                                                                                                                                             |                                                                |                                                                                                                       |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                |                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                          | +
-|**Create a Visual3D hybrid model** is the extension to the Visual3D 6 degree of freedom model which was developed in collaboration with the National Institutes of Health, Physical Disabilities Branch.\\ \\ The main extension to the model is that the pose (Position and Orientation) of a segment can depend on data from other segments. If data from other segments is used, the segment no longer has 6 degrees of freedom. For example, a thigh segment could be created using a hip joint landmark, which was defined relative to the pelvis segment.\\ \\ <code>\\ Create_Hybrid_Model\\ </code>  |/CALIBRATION_FILE= the name of the c3d file for the static trial|/SUFFIX= a suffix that is added to the Calibration_File if and only if the c3d file for the static trial already exists|/RANGE=ALL_FRAMES\\ \\ <code>\\ ;\\ </code>\\ \\ **Note: Wildcards (*) can be used for the Calibration_File name**\\ \\ **Note:** If the Calibration_File is specified and the file does not exist in the Workspace, the Suffix is ignored.\\ \\ **Note:** If the Calibration_File is specified and the file exists in the Workspace, the suffix is automatically added to the model name.\\ \\ **Note:** If the Calibration_File is specified and the suffix is specified, but the Filename and the Filenam+Suffix exists in the Workspace, the user is prompted for a new name.\\ \\ The example below creates a model using frames 10 to 15 of the static trial:\\ \\ <code>\\ Create_Hybrid_Model\\ /CALIBRATION_FILE= *static.c3d\\ </code>|/SUFFIX= a suffix that is added to the Calibration_File if and only if the c3d file for the static trial already exists.\\ \\ <code>\\ /RANGE=10+15\\ ;\\ \\ Set_Pipeline_Parameter_To_Folder_Path\\ /PARAMETER_NAME=FOLDER\\ /PARAMETER_VALUE=c:\exampleData\\\ ;\\ \\ Set_Pipeline_Parameter\\ /PARAMETER_NAME=STANDING\\ /PARAMETER_VALUE=::FOLDER&*static.c3d\\ ;\\ \\ Create_Hybrid_Model\\ /CALIBRATION_FILE=::STANDING\\ ;\\ </code>\\ \\ Another example can be found on [[Visual3D:Documentation:Pipeline:Model_Commands:Create_Hybrid_Model_Example|Pipeline Example using Create Hybrid Model]]|+
  
-[[visual3d:documentation:pipeline:model_commands:Append_Model_Template]]+[[Visual3D:Documentation:Pipeline:Model_Commands:Create_Hybrid_Model|Create a Hybrid Model]] is the extension to the Visual3D 6 degree of freedom model which was developed in collaboration with the  
 +National Institutes of Health, Physical Disabilities Branch.\\ 
 +The main extension to the model is that the pose (Position and Orientation) of a segment can depend on data from other segments.  
 +If data from other segments is used, the segment no longer has 6 degrees of freedom.  
 +For example, a thigh segment could be created using a hip joint landmark, which was defined relative to the pelvis segment.
  
-Append a template to an existing model.+<code> 
 +Create_Hybrid_Model 
 +/CALIBRATION_FILE= the name of the c3d file for the static trial 
 +/SUFFIX= a suffix that is added to the Calibration_File if and only if the c3d file for the static trial already exists 
 +/RANGE=ALL_FRAMES 
 +; 
 +</code>
  
-**Append_Model_Template** +**Note: Wildcards (*) can be used for the Calibration_File name**\\  
-! /CALIBRATION_FILE= +**Note:** If the Calibration_File is specified and the file does not exist in the Workspace, the Suffix is ignored.\\  
-! /MODEL_TEMPLATE= +**Note:** If the Calibration_File is specified and the file exists in the Workspace, the suffix is automatically added to the model name.\\ 
-! /VIEW_BUILDMODEL_RESULTS=2 +**Note:** If the Calibration_File is specified and the suffix is specified, but the Filename and the Filenam+Suffix exists in the Workspace, the user is prompted for a new name.
-**;** +
-=== Modeling ===+
  
-== Add_Landmark ==+The example below creates a model using frames 10 to 15 of the static trial: 
 + 
 +<code> 
 +Create_Hybrid_Model 
 +/CALIBRATION_FILE= *static.c3d 
 +/SUFFIX= a suffix that is added to the Calibration_File if and only if the c3d file for the static trial already exists. 
 +/RANGE=10+15 
 +; 
 + 
 +Set_Pipeline_Parameter_To_Folder_Path 
 +/PARAMETER_NAME=FOLDER 
 +/PARAMETER_VALUE=c:\exampleData 
 +; 
 + 
 +Set_Pipeline_Parameter 
 +/PARAMETER_NAME=STANDING 
 +/PARAMETER_VALUE=::FOLDER&*static.c3d 
 +; 
 + 
 +Create_Hybrid_Model 
 +/CALIBRATION_FILE=::STANDING 
 +; 
 +</code> 
 + 
 +Another example can be found on [[Visual3D:Documentation:Pipeline:Model_Commands:Create_Hybrid_Model_Example|Pipeline Example using Create Hybrid Model]] 
 + 
 +===== Modeling ===== 
 + 
 +==== Add_Landmark ==== 
 + 
 +[[visual3d:documentation:pipeline:model_commands:add_landmark]]
  
 == Add_Landmark_from_Event == == Add_Landmark_from_Event ==
 +
 +[[visual3d:documentation:pipeline:model_commands:add_landmark_from_event]]
  
 == Add_Functional_Joint_Landmark == == Add_Functional_Joint_Landmark ==
 +
 +[[visual3d:documentation:pipeline:model_commands:add_functional_joint_landmark]]
  
 == Modify_Landmark == == Modify_Landmark ==
 +
 +[[visual3d:documentation:pipeline:model_commands:modify_landmark]]
  
 == Associate_Functional_Joints_With_Files == == Associate_Functional_Joints_With_Files ==
 +
 +[[visual3d:documentation:pipeline:model_commands:Associate_Functional_Joints_With_Files]]
  
 Associate a movement trial with a Functional Landmark Associate a movement trial with a Functional Landmark
 +
 == Associate_Digitizing_Landmarks_With_Files == == Associate_Digitizing_Landmarks_With_Files ==
 +
 +[[visual3d:documentation:pipeline:model_commands:Associate_Digitizing_Landmarks_With_Files]]
  
 Associate a movement trial with a Digitizing Landmark Associate a movement trial with a Digitizing Landmark
visual3d/documentation/pipeline/model_commands/model_commands_overview.1731419423.txt.gz · Last modified: 2024/11/12 13:50 by wikisysop